杭州防水補漏殺蟲漆分析防水補漏白蟻防治固化劑產品
固化劑在水下、潮濕、干燥、低溫（0℃以下）、常溫條件下均能固化防水補漏白蟻防治樹脂，并獲得優良水下粘接強度。能滿足水工建筑工程要求，便利于冬季施工，該固化劑毒性低（LD>5000mg/kg）屬微毒或?qū)嶋H無毒化合物。并且有一定的耐熱、耐寒性能。適應于大壩、隧洞、輸水管、水池、渡槽、人防工程等建筑物的缺陷處理，以及其他水泥制品的水下粘接和戶外低溫施工。近年又廣泛應用于冶金、冶煉、礦山機械鑄造、模具造型，軍工防腐，地下電纜封端、護層，民品用膠。可用于水利、冶金、化工、等領域的設備和管道防腐、固化防腐涂層、石油化工方面防腐堵漏、水利工程、土木建筑工程中的混凝土石料、鋼材、瓷磚等材料粘接、嵌縫和涂料行業、玻璃鋼行業及防水補漏白蟻防治的中涂、底涂等。

固化劑用量要求不嚴格，視環境條件而定，一般用量為環杭州防水補漏殺蟲漆汕頭空調官方授權維修點18675439769氧地坪樹脂（E-51）用量的18~30%，室溫固化24h后可以達到80%以上的固化度。通常情況、室溫、干燥天氣施工時，用量可以選擇20~30%，如果在低溫、潮濕、水下條件時施工用量可增加為25~35%。

應用事例：某化工廠有一耐酸池，體積為20m3，使用溫度為70～80℃，酸含量為10～15%。原來采用耐酸瓷磚貼面處理，但由于磚縫處理不好，造成池壁滲漏。2003年后改用我院研制的本固化劑與環氧樹脂制作玻璃鋼，使用至今毫無損壞。

某大壩建設于上世紀60年代，長期使用后因出現裂縫而滲水，并處于寒冷地區，使用本固化劑配合環氧樹脂及其他輔助材料調漿灌縫，固化速度快，起到了很好的堵漏作用，延長了大壩的使用壽命。使用至今毫無損壞。

Curing agent under water, wet, dry and low temperature (below 0 ℃) can, under the condition of room temperature curing epoxy resin, and obtain good underwater bonding strength. Can satisfy the requirement of hydraulic structure engineering, convenience in winter construction, low toxicity of the curing agent (LD > 5000 mg/kg) WeiDu or actual non-toxic compound. And a certain heat resistant, cold resistant performance. Its adaptation, tunnel, water pipe, the building such as pool, aqueduct, civil air defense engineering defects, and other underwater adhesive cement products and outdoor construction in low temperature. In recent years and widely used in metallurgy, metallurgy, mining machinery casting, mold modelling, military industry anticorrosion, underground cable sealing side, the sheath, civilian goods with glue. Can be used in water conservancy, metallurgy, chemical industry, in areas such as equipment and pipeline corrosion and anticorrosion coating, petroleum chemical industry curing in flood protection, water conservancy engineering, civil engineering and construction engineering materials such as concrete, stone, steel, ceramic tile adhesive, sealing and coating industry, glass fiber reinforced plastic industry and epoxy floor coating, coating, etc.
Curing agent dosage is not strict, depending on environmental conditions, the general dosage for the dosage of epoxy resin (E - 51) of 18 ~ 30%, room temperature curing after 24 h can reach more than 80% of the curing degree. Usually, at room temperature, dry construction, can choose 20 ~ 30%, if the condition of low temperature, humidity, underwater construction dosage can increase to 25 ~ 35%.
Application example: a chemical plant one acid pool, volume of 20 m3, using temperature is 70 ~ 80 ℃, the acid content of 10 ~ 15%. Original use acid-resistant ceramic tile face processing, but because of bad brick joints treatment caused the leakage of the wall. To switch to our hospital to develop after 2003 the production of glass fiber reinforced plastic with epoxy resin curing agent has no damage.
Developed by our hospital this curing agent has been widely used in the north cold season construction, curing rate significantly faster than domestic with other types of curing agent, is well received by users.
A dam construction in the 1960 s, due to cracks after long-term use of ooze water, and in cold region, the use of the curing agent with epoxy resin and other auxiliary materials mixing seam, curing speed, has played a very good plugging effect and prolong the service life of the dam. Use up to now there is no damage.
http://www.5022777.com/7scp/dtl8-5.htm